Can Old Concrete Be Stained | Concrete Stain Is Permanent | Test for Old Sealants | Color Test the Concrete

Can Old Concrete Be Stained | Concrete Stain Is Permanent | Test for Old Sealants | Color Test the Concrete

Can Old Concrete Be Stained?

Can Old Concrete Be Stained?

The most prevalent question we are questioned relating to old concrete is that of staining of them. Concrete patios and walkways are attractive to be looked at but with the passage of time become out-dated.

The answer to whether old concrete can be stained is yes. They can be acid stained. The process for doing so is not quite difficult to be done, just a few appropriate pieces of information are to be known, along with some extra steps to be taken.

Acid stains are nothing but coloured washes, which are to be soaked into the pores present in concrete. Unlike paints, stains are not surface covering in nature.

If the stain is not getting soaked into the pores of the concrete, then it will not be able to cover as required. This in turn indicates that old concrete will not be able to get sealed, or painted when it is to be stained or to be coated with epoxy.

The age of the concrete does not relate to the stain’s effectiveness while the condition of the concrete is the determining factor. We should remain away from paint and acrylics as both are masked as paints. They act as surface covering but not as our required stains.

By applying the above materials, they will not be absorbed into the old concrete in the required time. Therefore with the passage of time, they will get husked up and will look disgusting. Again, restoring them it will cost you money in the long run.

The stain which will be real in nature forms a chemical reaction, that will permanently change the concrete’s colour.

While staining old concrete, at any cost, it is to be made sure that the surface should be properly cleaned, free from any kind of stains, old paints and true acid stain should be used.

Concrete Stain Is Permanent?

Concrete Stain Is Permanent?

It is to kept in mind that once the old concrete surface is stained, the colour will be permanent. Stain will penetrate and be absorbed into the pores of concrete. There will be no way left to remove the stain once applied.

Unlike paint or acrylic stain will not be a surface leveller. Colour sampling should be done on concrete, before a stain is to be applied, especially while working in indoor conditions.

Acid stains might sometimes be impossible to be removed and can be tough in nature.

Also Read: All About Bathroom Doors | Should Bathroom Doors Open in or Out | Bathroom Doors Should Open Inward or Outward | Reasons Bathroom Doors Swing Inward

Can Your Old Concrete Be Stained?

Can Your Old Concrete Be Stained

It is a fun and convenient way to freshen up old concrete surfaces by staining old concrete surface. Just while staining the concrete must be clean and made free from any kind of debris. The quality of staining depends on the condition of the concrete.

At times new concrete can not be stained also if the surface is grimy, dirty, and covered with paint or sealant. For staining your concrete, it must be clean and bare surface.

It is so, due to the working characteristic of acid stain. Acid concrete stains are thin mixtures consisting of chemicals and colour. As soon as it is poured on the surface of old concrete, it gets absorbed into the pores of concrete and colour is created.

Due to the above process if dirt will be present, the pores will be filled which in-turn will obstruct acid stain to be soaked into pores. Any sort of material can lead to filling of pores, but the most prominent among them are sealers, dirt, paint, and grime.

Paint, sealant coats, and epoxy seep into the concrete pores and blocks them. So, in that case, the oldness of concrete will not be a factor for effective staining the blockage will be the obstructing factor for getting the proper results.

The best thing is regardless of the concrete’s age the surface can be properly stained regardless of the fact the surface is properly cleaned. If a condition arises that older concrete surface has got paint on it or is sealed there is nothing to worry about. Few ways are available to get them removed.

Just muriatic acid should not be applied for cleaning the paint as it will lead to the destruction of important required minerals which are essential for production of colour range which we want from concrete stain.

Removing Paint

Removing Paint

  • Industrial paint remover is the best way for removing paint from the required concrete surface. It is to be laid on the surface and then waited for it to work.
  • Paint removers result in lifting off the paint on concrete.
  • Once it is seen that the paint softens and starts to lift from the concrete surface, a hand scraper or power washer is to be taken and remove as much paint can be removed.
  • Everything can not be removed at one go, so repeated action should be done as required for proper completion.
  • After removal of total paint, the surface should be cleaned and dried properly.

Removing Sealant

Removing Sealant

  • For protecting concrete from water damage, a sealant is to be used. It is generally recommended for any concrete patio surface. This sealant prevents the proper application of stain, as the sealant will penetrate the pores and result in blockage.
  • A seal and stain can be used together, following one rule, i.e., the stain should be applied first. After that sealant is to be applied.
  • Removal of paint is much easier than sealant to be removed. With the passage of time sealer fades away, for this reason, reseal of concrete is mandatory. If someone does not need to wait for the fading away of sealant, a pressure washer should be used for washing away the sealant.
  • For the removal of tough sealant, you can try Xylene.
  • The material is poured on concrete, then let it settle for about 30 seconds, then it is to be use a stiff brush to scrub off. At last use scraper for removing sealer. Repeat if required.

Removing Wax

Removing Wax

  • If wax has built up on the surface of the concrete, a floor wax remover is required.
  • The floor wax remover is to be applied on the old surface, then let it sit for a certain time, after that scrub off with soft bristle brush.
  • Until the floor wax is properly removed mop the affected area.

Removing Epoxy

Removing Epoxy

  • For finishing the concrete epoxy is used sometimes and staining will not be possible. So, the epoxy finish must be removed prior to the application of staining.
  • The most hard to remove material is epoxy as compared to sealer and paint.

Most effective ways for removal of epoxy from concrete are:

  • Acetone– The concrete is to be soaked in acetone and then you need to wait to get them soft so that they can be scrapped off.
  • Heat Gun– Evaporate and peel off the epoxy from the concrete surface, at a single time small sections are done part by part
  • Paint Thinner– Same method should be used as used with acetone.
  • Sanding– This option is an extreme category, but the top layer of concrete can be covered with sand. Doing so, will help in removal of traces of acrylic and in-turn a smooth surface will be created for staining.
  • A combined material of above three methods can also be used. The concrete is to be soaked in either acetone of paint thinner and scraped when ready. Heat gun can be used for hardening the clean areas.

Also Read: All About Concrete Countertops Be Painted | Can Concrete Countertops Be Painted | How to Paint Concrete Countertops

Acid Staining Old Concrete


Acid Staining Old Concrete

  • It is to be remembered that staining old concrete is not a big difference than staining new concrete. It all depends on the condition of concrete. As soon as it is clean and dried the surface can be stained.
  • Old concrete will have dirt, sealant, paint, mildew, or substances entrapped in the pores of the concrete. Cleaning is the most essential step which should not be skipped.
  • Just after cleaning the major issues which will affect the effectiveness of stain like, old sealant, paint, or acrylic is removed, the concrete is to be cleaned by mopping, sweeping, and scrubbing them with the help of concrete wash or just simple soap with hot water.
  • If by any chance dirt, dust, pollen or other substances are left by on the concrete, after staining is done they can be noticed.

Test for Old Sealants

Test for Old Sealants

  • It is to be made sure that bare and clean concrete is stained, and a test is to be conducted to make that sure.
  • The best way to test so, is by pouring little water over the entire required surface. As soon as you see the water gets soaked, staining can be started.
  • Whereas if water gets puffed on the surface or gets blocked on the surface, then further cleaning is required.
  • Acrylic and paints are easy to get spotted. Anywhere on the concrete surface can be cleaned off that is not bare concrete.
  • A test like above mentioned can be performed in the last step, since if some extra sealant gets remained on the surface, then that also can be cleaned before staining.
  • Otherwise, if that not done the areas will not hold stain then the concrete will be looking blotchy.

Also Read: Should Concrete Walls Be Insulated | Why Concrete Is Bad at Insulating | Benefits of Insulating Concrete | Best Insulation to Use with Concrete

Color Test the Concrete

Color Test the Concrete

  • Stains might get a different look when applied on actual concrete, rather than on a test swab or picture. Stains undergo a reaction when applied on concrete.
  • It is not the same as applying paints where the colour will be exactly same as the sample. For this reason, some testing is to be done.
  • On the small test area apply some stain, just before you stain the entire surface. Then an area is to be picked that will not be noticed.
  • Then stain a very minimal spot then see what the colour will look like when dried.
  • If the colour is not liked by you, adjustment can be done as required and then again tested.

Frequently Asked Question(FAQ):

Can Old Concrete Be Stained?

Your existing old concrete should be fine to stain, so long as it is not contaminated with glue, paint, oil, grease, sealers, waxes, or anything else that would prevent the stain from soaking into the pores of the concrete.

Do Leaves Permanently Stain Concrete?

Leaf marks on concrete are not permanent, but they can be difficult to remove. The same organic substances that create color in the leaves can stain a concrete surface. Fresh stains are easier to remove than older stains.

Cost of Stained Concrete Floor

Stained Concrete Cost – $2 to $4 per square foot. Concrete Overlay Cost – $3 to $7 per square foot. Polished Concrete Cost – $3 to $12 per square foot.

Cost Per Sq Ft to Stain Concrete

How Much Does it Cost to Stain Concrete? The cost of stained concrete can vary greatly. For a basic application of a single stain color with sealer and minimal surface prep, most decorative concrete contractors charge between $2 and $5 per square foot. As the complexity of the job rises, so will the price.

Cost to Acid Stain Concrete

Acid-based concrete stain

The cost to install acid stains is around $2 to $6 per square foot for basic designs or $12 to $25 per square foot for complex colors and patterns.

Cost to Stain Concrete Driveway

Staining an existing driveway will cost $2 – $4 per sq. ft. Combining that with the average driveway size, it would cost between $1,280 – $2,560.

How to Get Old Oil Stain Out of Concrete?

Spray the stain with oven cleaner and let it sit for 5 to 10 minutes. Use a stiff brush to scrub the spot. Then, rinse with a hose at its highest pressure. If the stain is still there, repeat the process.

How to Remove Old Oil Stains from Driveway?

Remove the oil stain with baking soda using these simple steps:

  1. Sprinkle a thick layer of baking soda over the oil stain in your driveway.
  2. Let it soak in for thirty minutes.
  3. Clean the stain by scrubbing it with a bristle brush.
  4. Wash away the baking soda with clean water.
  5. Repeat if necessary.

What Is the Best Sealer for Stained Concrete?

One of the very best sealers on the market today for acid-stained concrete and other types of decorative concrete flooring is the “polyurea“. Polyurea is extremely durable, long-lasting and easy to maintain. Most clear sealers for concrete come in water and solvent-based versions.

What Is Acid Stained Concrete Floors?

Acid staining is a finishing technique for concrete that mixes water, hydrochloric acid, and acid-soluble metallic salts. This mixture penetrates and chemically reacts with the hydrated lime in the concrete. The stain lightly etches the concrete surface, which allows the metallic salts to penetrate easier.

How to Remove Stains from Polished Concrete Floors?

How do I clean spills on a concrete floor? With any spill on a polished concrete floor, you should first mop up as much of the spill as possible using a paper towel or rag. Next, clean the entire area with a warm soap and water mixture to dilute and neutralize any remaining residue.

How to Fix Stained Concrete?

Removing dirt and foliage stains on concrete

  1. Sweep away all debris and dirt.
  2. Mix liquid dishwashing detergent and water in a spray bottle or bucket for larger stains.
  3. Apply the detergent and water mixture to the stain.
  4. Let it sit for 15 minutes.
  5. Scrub with a soft brush.
  6. Rinse the area and repeat if necessary.

How Much Does Concrete Staining Cost Per Square Foot?

How Much Does it Cost to Stain Concrete? The cost of stained concrete can vary greatly. For a basic application of a single stain color with sealer and minimal surface prep, most decorative concrete contractors charge between $2 and $5 per square foot. As the complexity of the job rises, so will the price.

How to Get Wax Stain Off Concrete?

How can I remove it? A: Harden the wax by setting a plastic bag filled with ice and water on it, and then scrape off as much as you can. Then use acetone or mineral spirits to remove the rest of the wax, the National Training Center for Stone and Masonry Trades recommends.

Acid Stained Concrete Floors Cost

How Much Do Acid Stained Concrete Floors Cost? The cost of acid stained floors begins at $0.47 per square foot, which is far less than tile, carpet, marble, or other common flooring options. Depending on design and surface conditions, costs can rise as high as $10.00 per square foot!

How to Remove Paint Stain from Concrete?

A deeper look at how to remove paint from concrete

  1. Give the concrete surface a deep cleaning and allow it to dry.
  2. Apply a paint stripper.
  3. Give the paint stripper some time to set.
  4. Scrub the surface.
  5. Follow up the scrubbing with a power wash.
  6. Repeat the process as necessary until all the paint is removed.

How to Remove Behr Concrete Stain?

  1. Remove loose or peeling stain with a wire brush and coarse sandpaper. Sweep or vacuum up the debris and discard.
  2. Clean the mop and broom thoroughly with liquid detergent and water. Wring or shake out excess water.
  3. Use a roller or clean rag mop to spread an even layer of Behr Concrete & Masonry Bonding Primer No.

How to Remove Concrete Stain and Sealer?

There are two methods for removing sealers from concrete:

  1. Mechanical, which consists of grinding, blasting or sanding the coating off the surface.
  2. Chemical, using a chemical stripper to remove the the coating.

Acid Stain Old Concrete

Acid staining is a chemical reaction that permanently changes the color of the concrete surface. If you want to stain old concrete, using a true acid stain is always the best option. Avoid “acrylic stains” as these are disguised paint and will also peel with time.

How to Remove Old Grease Stains from Concrete?

Putting a paste of powdered laundry detergent and water on the stain, says After letting it sit, scrub it with a broom or brush and rinse the spot off with water. Scrubbing the stain with a grease-cutting dish detergent and a stiff broom, according to

Like this post? Share it with your friends!

Suggested Read-

Leave a Reply

Your email address will not be published. Required fields are marked *